Automatic Dependent Surveillance–Broadcast
![](http://upload.wikimedia.org/wikipedia/commons/thumb/e/ee/FAA_NextGen_ADS-B_implementation.jpg/220px-FAA_NextGen_ADS-B_implementation.jpg)
Automatic Dependent Surveillance–Broadcast (ADS-B) is an aviation surveillance technology and form of electronic conspicuity in which an aircraft (or other airborne vehicles such as drones approved to fit "ADS-B Out") determines its position via satellite navigation or other sensors and periodically broadcasts its position and other related data, enabling it to be tracked. The information can be received by air traffic control ground-based or satellite-based receivers as a replacement for secondary surveillance radar (SSR). Unlike SSR, ADS-B does not require an interrogation signal from the ground or from other aircraft to activate its transmissions. ADS-B can also receive point-to-point by other nearby equipped "ADS-B In" equipped aircraft (or drones) to provide traffic situational awareness and support self-separation. ADS-B is "automatic" in that it requires no pilot or external input to trigger its transmissions. It is "dependent" in that it depends on data from the aircraft's navigation system to provide the transmitted data.[1]
ADS-B is a key part of the International Civil Aviation Organization's (ICAO) approved aviation surveillance technologies and is being progressively incorporated into national airspaces worldwide. For example, it is an element of the United States Next Generation Air Transportation System (NextGen), the Single European Sky ATM Research project (SESAR), and India's Aviation System Block Upgrade (ASBU).[2][3][4] ADS-B equipment is mandatory for instrument flight rules (IFR) category aircraft in Australian airspace; the United States has required many aircraft (including all commercial passenger carriers and aircraft flying in areas that required a SSR transponder) to be so equipped since January 2020; and, the equipment has been mandatory for some aircraft in Europe since 2017.[5][6][7] Canada uses ADS-B for surveillance in remote regions not covered by traditional radar (areas around Hudson Bay, the Labrador Sea, Davis Strait, Baffin Bay and southern Greenland) since January 15, 2009.[8][9] Aircraft operators are encouraged to install ADS-B products that are interoperable with US and European standards, and Canadian air traffic controllers can provide better and more fuel-efficient flight routes when operators can be tracked via ADS-B.[10][11]
Description
ADS-B is an airspace surveillance system which could eventually replace Secondary surveillance radar as the main surveillance method for controlling aircraft worldwide. In the United States ADS-B is an integral component of the NextGen national airspace strategy for upgrading and enhancing aviation infrastructure and operations.[12]
ADS-B enhances safety by making an aircraft visible, realtime, to air traffic control (ATC) and to other ADS-B In equipped aircraft with position and velocity data transmitted every second. Other uses of ADS-B data include: post-flight analysis, inexpensive flight tracking, planning, and dispatch.[12]
Within the United States, the ADS-B system has the ability to provide air traffic and government-generated graphical weather information at no cost through TIS-B and FIS-B applications.[12]
ADS-B consists of two distinct functions - "ADS-B Out" and "ADS-B In". Each "ADS-B Out" aircraft periodically broadcasts information about itself, such as identification, current position, altitude and velocity through an onboard transmitter. ADS-B Out provides air traffic controllers with real-time aircraft position information that is, in most cases, more accurate than the information available with current radar-based systems. With more accurate information, ATC can manage and separate aircraft with improved precision and timing.[13]
"ADS-B In" is the reception and processing of transmitted ADS-B information (i.e. "ADS-B Out") by other aircraft. In the US ADS-B In can also include other information for pilots transmitted from ATC ground stations such as FIS-B and TIS-B data.[13] These ground station data broadcasts are typically made available only when an ADS-B Out broadcasting aircraft is nearby.[14]
The ADS-B Out system relies on two avionics components aboard each aircraft: a high-integrity satellite navigation source (i.e. GPS or other certified GNSS receiver) and a datalink (the ADS-B unit). There are several types of certified ADS-B data links, but the most common ones operate at 1090 MHz, essentially a modified Mode S transponder, or at 978 MHz.[12] The FAA would like to see aircraft that operate exclusively below 18,000 feet (5,500 m) use the 978 MHz link, as this will alleviate congestion of the 1090 MHz frequency.[15] To obtain ADS-B Out capability at 1090 MHz, user-operators can install a new transponder or modify an existing transponder if the manufacturer offers an ADS-B upgrade (plus install a certified GNSS position source if one is not already present).[12]
Benefits
ADS-B provides many benefits to both pilots and air traffic control that improve both the safety and efficiency of flight.[16][17]
When using an ADS-B In system, a pilot is able to view traffic information about surrounding aircraft if those aircraft are equipped with ADS-B Out. This information includes altitude, heading, speed, and distance to the aircraft. In addition to receiving position reports from ADS-B Out participants, in the US, TIS-B can provide position reports on non-ADS-B Out-equipped aircraft if suitable ground equipment and ground radar exist. ADS-R re-transmits ADS-B position reports between UAT and 1090 MHz frequency bands.
Aircraft equipped with universal access transceiver (UAT) ADS-B In technology will be able to receive weather reports, and in the US, weather radar through flight information service-broadcast (FIS-B), which also transmits readable flight information such as temporary flight restrictions (TFRs) and NOTAMs.
ADS-B ground stations are significantly cheaper to install and operate compared to primary and secondary radar systems used by air traffic control for aircraft separation and control.
Unlike some alternative in-flight weather services currently being offered commercially, there will be no subscription fees to use ADS-B services or its various benefits in the US. The aircraft owner will pay for the equipment and installation, while the Federal Aviation Administration (FAA) will pay for administering and broadcasting all the services related to the technology.
Safety
- Situational awareness
ADS-B makes flying significantly safer for the aviation community by providing pilots with improved situational awareness. Pilots in an ADS-B In equipped cockpit will have the ability to see, on their in-cockpit flight display, other traffic operating in the airspace and have access to clear and detailed weather information. They will also be able to receive pertinent updates ranging from temporary flight restrictions to runway closings.
- Improved visibility
Even aircraft only equipped with ADS-B Out will benefit from air traffic controllers' ability to more accurately and reliably monitor their position. When using this system both pilots and controllers will see the same radar picture. Other fully equipped aircraft using the airspace around them will be able to more easily identify and avoid conflict with an aircraft equipped with ADS-B Out. With past systems such as the Traffic alert and Collision Avoidance System (TCAS) aircraft could only see other aircraft equipped with the same technology. With ADS-B, information is sent to aircraft using ADS-B In, which displays all aircraft in the area, provided those aircraft are equipped with ADS-B Out. ADS-B provides better surveillance in fringe areas of radar coverage. ADS-B does not have the siting limitations of radar. Its accuracy is consistent throughout the range.[18] In both forms of ADS-B (1090ES & 978 MHz UAT), the position report is updated once per second. The 978 MHz UAT provides the information in a single, short-duration transmission. The 1090ES system transmits two different kinds of position reports (even/odd) randomly. To decode the position unambiguously, one position report of both kinds or a reference position nearby is needed.
ADS-B enables improved safety by providing:[19]
- Radar-like IFR separation in non-radar airspace
- Increased VFR flight following coverage
- ATC final approach and runway occupancy, reducing runway incursions on the ground
- More accurate search and rescue response[19] — although ADS-B can transmit "aircraft down" data, the FAA has stated that there is no intention to perform even a study of ADS-B's effectiveness in an "aircraft down" situation, simply based on the fact that ADS-B equipment has no requirement to be crashworthy, as compared to the current "black box" recorder.[citation needed] ADS-B was demonstrated to the Civil Air Patrol (CAP) in March 2003 by AOPA via flight demonstrations for possible integration of the technology in CAP activities.[20]
- Helps pilots to see and avoid other aircraft
- Cockpit final approach and runway occupancy
- Visual separation in VFR and MVFR conditions
- VFR-like separation in all weather conditions
- Real-time cockpit weather display
- Real-time cockpit airspace display
Efficiency
- Reduced environmental impact
ADS-B technology provides a more accurate report of an aircraft's position.[21] This allows controllers to guide aircraft into and out of crowded airspace with smaller separation standards than it was previously possible to do safely. This reduces the amount of time aircraft must spend waiting for clearances, being vectored for spacing and holding. Estimates show that this is already having a beneficial impact by reducing pollution and fuel consumption.[22]
- Traffic capacity improvement
ADS-B enables increased capacity and efficiency by supporting:
- Better ATC traffic flow management[19]
- Merging and spacing[19]
- Self-separation or station keeping[19]
- Enhanced visual approaches;
- Closely spaced parallel approaches;
- Reduced spacing on final approach;
- Reduced aircraft separations;
- Enhanced operations in high altitude airspace for the incremental evolution of the "free flight" concept;
- Surface operations in lower visibility conditions;
- Near visual meteorological conditions (VMC) capacities throughout the airspace in most weather conditions;
- Improved air traffic control services in non-radar airspace;
- Trajectory-based operations provide a gently ascending and descending gradient with no step-downs or holding patterns needed. This will produce optimal trajectories with each aircraft becoming one node within a system-wide information management network connecting all equipped parties in the air and on the ground. With all parties equipped with NextGen equipment, benefits will include reduced gate-to-gate travel times, increased runway utilization capacity, and increased efficiency with carbon conservation.
- Use of ADS-B and CDTI may allow decreased approach spacing at certain airports to improve capacity during reduced-visibility operations when visual approach operations would normally be terminated (e.g., ceilings less than MVA +500).[citation needed]
Other applications
The ADS-B data link supports a number of airborne and ground applications. Each application has its own operational concepts, algorithms, procedures, standards, and user training.[citation needed]
- Cockpit display of traffic information
A cockpit display of traffic information (CDTI) is a generic display that provides the flight crew with surveillance information about other aircraft, including their position. Traffic information for a CDTI may be obtained from one or multiple sources, including ADS-B, TCAS, and TIS-B. Direct air-to-air transmission of ADS-B messages supports the display of proximate aircraft on a CDTI.[citation needed]
In addition to traffic based on ADS-B reports, a CDTI function might also display current weather conditions, terrain, airspace structure, obstructions, detailed airport maps, and other information relevant to the particular phase of flight.[23]
- Airborne collision avoidance
ADS-B is seen as a valuable technology to enhance airborne collision avoidance system (ACAS) operation. Incorporation of ADS-B can provide benefits such as:
- Decreasing the number of active interrogations required by ACAS, thus increasing effective range in high-density airspace.[citation needed]
- Reducing unnecessary alarm rate by incorporating the ADS-B state vector, aircraft intent, and other information.[citation needed]
- Use of the ACAS display as a CDTI, providing positive identification of traffic.[citation needed]
- Extending collision avoidance below 1,000 feet above ground level, and detecting runway incursions.[citation needed]
Eventually, the ACAS function may be provided based solely on ADS-B, without requiring active interrogations of other aircraft transponders.[23]
Other applications that may benefit from ADS-B include:
- Lighting control automation and operation
- Airport ground vehicle and aircraft rescue and firefighting vehicle operational needs
- Altitude height keeping performance measurements
- General aviation operations control[23]
- Conflict management
- ATS conformance monitoring
- Aircraft spotting where personal receivers can be used to produce a virtual radar picture
- A number of websites use crowd-sourced distributed networks of ADS-B receivers to track air traffic.
Security risk
Aircraft with transponder only, or no transponder capability at all will not be shown. Pilots who become complacent or overconfident in this system are thus a safety problem, not only for themselves but for other transponder-only aircraft, and glider aircraft without ADS-B transponder.
Glider aircraft often use the FLARM system for collision avoidance with other glider aircraft, but this system is not compatible with ADS-B. Aircraft with ADS-B but without FLARM are thus a safety risk for gliders with FLARM but without ADS-B and vice versa. Some aircraft, like those used for towing gliders, have both FLARM and ADS-B transponders for this reason.
A security researcher claimed in 2012 that ADS-B has no defence against being interfered with via spoofed ADS-B messages because they were neither encrypted nor authenticated.[24] The FAA responded to this criticism saying that they were aware of the issues and risks but were unable to disclose how they are mitigated as that is classified. A possible mitigation is multilateration to verify that the claimed position is close to the position from which the message was broadcast. Here the timing of received messages is compared to establish distances from the antenna to the plane.[25]
The lack of any authentication within the standard makes it mandatory to validate any received data by use of the primary radar. Because the content of ADS-B messages is not encrypted, it may be read by anybody.[26]
![](http://upload.wikimedia.org/wikipedia/commons/thumb/f/f1/Adscapture.png/220px-Adscapture.png)
Theory of operation
![](http://upload.wikimedia.org/wikipedia/commons/thumb/9/92/AERO_Friedrichshafen_2018%2C_Friedrichshafen_%281X7A4803%29.jpg/220px-AERO_Friedrichshafen_2018%2C_Friedrichshafen_%281X7A4803%29.jpg)
The ADS-B system has three main components: 1) ground infrastructure, 2) airborne component, and 3) operating procedures.[27]
- A transmitting subsystem that includes message generation and transmission functions at the source; e.g., aircraft.[citation needed]
- The transport protocol; e.g., VHF (VDL mode 2 or 4), 1090ES, or 978 MHz UAT.[citation needed]
- A receiving subsystem that includes message reception and report assembly functions at the receiving destination; e.g., other aircraft, vehicle or ground system.[citation needed]
The source of the state vector and other transmitted information as well as user applications are not considered to be part of the ADS-B system.[23]
Physical layer
Two link solutions are used as the physical layer for relaying ADS-B position reports: universal access transceiver,[28] and 1090 MHz extended squitter.[29][30]
Universal Access Transceiver (UAT)
A universal access transceiver is a data link intended to serve the majority of the general aviation community. The data link is approved in the Federal Aviation Administration's "final rule" for use in all airspace except class A (above 18,000 ft. MSL). UAT is intended to support not only ADS-B, but also flight information service – broadcast (FIS-B), traffic information service – broadcast (TIS-B), and, if required in the future, supplementary ranging and positioning capabilities.[31] Due to the set of standards required for this rule, it is seen as the most effective application for general aviation users. UAT will allow aircraft equipped with "out" broadcast capabilities to be seen by any other aircraft using ADS-B In technology as well as by FAA ground stations. Aircraft equipped with ADS-B In technology will be able to see detailed altitude and vector information from other ADS-B Out equipped aircraft as well as FIS-B and TIS-B broadcasts. The FIS-B broadcast will allow receiving aircraft to view weather and flight service information including AIRMETs, SIGMETs, METARs, SPECI, national NEXRAD, regional NEXRAD, D-NOTAMs, FDC-NOTAMs, PIREPs, special use airspace status, terminal area forecasts, amended terminal aerodrome forecasts (TAFs), and winds and temperatures aloft forecasts.[32] These broadcasts serve to provide early adopters of the technology with benefits as an incentive for more pilots to use the technology before 2020. Aircraft receiving traffic information through the TIS-B service will see other aircraft in a manner that is similar to how all aircraft will be seen after they have been equipped by 2020. The availability of a non-subscription weather information service, FIS-B, provides general aviation users with a useful alternative to other monthly or annual fee-based services.
The UAT system is specifically designed for ADS-B operation. UAT is also the first link to be certified for "radar-like" ATC services in the United States. Since 2001 it has been providing 5 nmi (9.3 km; 5.8 mi) en-route separation (the same as mosaic radar but not 3 nmi (5.6 km; 3.5 mi) of single-site sensors) in Alaska. UAT is the only ADS-B link standard that is truly bidirectional: UAT users have access to ground-based aeronautical data (FIS-B) and can receive reports from proximate traffic (TIS-B) through a multilink gateway service that provides ADS-B reports for 1090ES-equipped aircraft and non-ADS-B equipped radar traffic. UAT-equipped aircraft can also observe each other directly with high accuracy and minimal latency. Viable ADS-B UAT networks are being installed as part of the United States' NextGen air traffic system.
1090 MHz extended squitter
In 2002 the Federal Aviation Administration (FAA) announced a dual-link decision using the 1090 MHz extended squitter (1090 ES) link for air carrier and private or commercial operators of high-performance aircraft, and universal access transceiver link for the typical general aviation user.[33] In November 2012, the European Aviation Safety Agency confirmed that the European Union would also use 1090 ES for interoperability.[34] The format of extended squitter messages has been codified by the ICAO.[30]
With 1090 ES, the existing Mode S transponder (TSO C-112 or a standalone 1090 MHz transmitter) supports a message type known as the extended squitter message. It is a periodic message that provides position, velocity, time, and, in the future, intent. The basic ES does not offer intent since current flight management systems do not provide such data (called trajectory change points). To enable an aircraft to send an extended squitter message, the transponder is modified (TSO C-166A[35]) and aircraft position and other status information is routed to the transponder. ATC ground stations and aircraft equipped with traffic collision avoidance system (TCAS) already have the necessary 1090 MHz (Mode S) receivers to receive these signals, and would only require enhancements to accept and process the additional extended squitter information. As per the FAA ADS-B link decision, and the technical link standards, 1090 ES does not support FIS-B service.[33]
Relationship to surveillance radar
Radar directly measures the range and bearing of an aircraft from a ground-based antenna. The primary surveillance radar is usually a pulse radar. It continuously transmits high-power radio frequency (RF) pulses. Bearing is measured by the position of the rotating radar antenna when it receives the RF pulses that are reflected from the aircraft skin. The range is measured by measuring the time it takes for the RF energy to travel to and from the aircraft.
Primary surveillance radar does not require any cooperation from the aircraft. It is robust in the sense that surveillance outage failure modes are limited to those associated with the ground radar system. Secondary surveillance radar depends on active replies from the aircraft. Its failure modes include the transponder aboard the aircraft. Typical ADS-B aircraft installations use the output of the navigation unit for navigation and for cooperative surveillance, introducing a common failure mode that must be accommodated in air traffic surveillance systems.[23]
Type | Independent? | Cooperative? |
---|---|---|
Primary surveillance radar (PSR) | Yes: surveillance data derived by radar | No: does not depend on aircraft equipment |
Secondary surveillance radar (SSR) | No: surveillance data provided by aircraft transponder | Yes: requires aircraft to have a working ATCRBS transponder |
Automatic dependent surveillance (ADS-B) | No: surveillance data provided by aircraft | Yes: requires aircraft to have a working ADS-B function |
Source: DO-242A[23] |
The radiated beam becomes wider as the distance between the antenna and the aircraft becomes greater, making the position information less accurate. Additionally, detecting changes in aircraft velocity requires several radar sweeps that are spaced several seconds apart. In contrast, a system using ADS-B creates and listens for periodic position and intent reports from aircraft. These reports are generated based on the aircraft's navigation system and distributed via one or more of the ADS-B data links. The accuracy of the data is no longer susceptible to the position of the aircraft or the length of time between radar sweeps.[33] (However, the signal strength of the signal received from the aircraft at the ground station is still dependent on the range from the aircraft to the receiver, and interference, obstacles, or weather could degrade the integrity of the received signal enough to prevent the digital data from being decoded without errors. When the aircraft is farther away, the weaker received signal will tend to be more affected by the aforementioned adverse factors and is less likely to be received without errors. Error detection will allow errors to be recognized, so the system maintains full accuracy regardless of aircraft position when the signal can be received and decoded correctly. This advantage does not equate to a total indifference to the range of an aircraft from the ground station.)
Today's air traffic control (ATC) systems do not rely on coverage by a single radar. Instead, a multi-radar picture is presented via the ATC system's display to the controller. This improves the quality of the reported position of the aircraft, provides a measure of redundancy, and makes it possible to verify the output of the different radars against others. This verification can also use sensor data from other technologies, such as ADS-B and multilateration.[citation needed]
Relationship to ADS-A/ADS-C
There are two commonly recognized types of ADS for aircraft applications:
- ADS-addressed (ADS-A), also known as ADS-Contract (ADS-C)
- ADS-broadcast (ADS-B)
ADS-A is based on a negotiated one-to-one peer relationship between an aircraft providing ADS information and a ground facility requiring receipt of ADS messages. For example, ADS-A reports are employed in the Future Air Navigation System (FANS) using the Aircraft Communications Addressing and Reporting System (ACARS) as the communication protocol. During a flight over areas without radar coverage, e.g., oceanic and polar, reports are periodically sent by an aircraft to the controlling air traffic region.[23]
Traffic information service – broadcast (TIS–B)
Traffic information service – broadcast (TIS–B) supplements ADS-B's air-to-air services to provide complete situational awareness in the cockpit of all traffic known to the ATC system. TIS–B is an important service for an ADS-B link in airspace where not all aircraft are transmitting ADS-B information. The ground TIS–B station transmits surveillance target information on the ADS-B data link for unequipped targets or targets transmitting only on another ADS-B link.[citation needed]
TIS–B uplinks are derived from the best available ground surveillance sources:
- ground radars for primary and secondary targets[citation needed]
- multilateration systems for targets on the airport surface[36]
- ADS-B systems for targets equipped with a different ADS-B link[17]
Multilink gateway service
The multilink gateway service is a companion to TIS-B for achieving interoperability between different aircraft equipped with 1090ES or UAT by using ground-based relay stations. These aircraft cannot directly share air-to-air ADS-B data due to the different communication frequencies. In terminal areas, where both types of ADS-B link are in use, ADS-B/TIS-B ground stations use ground-to-air broadcasts to relay ADS-B reports received on one link to aircraft using the other link.[17]
Although multilink "solves" the issue of heavy airliners working on one frequency vs. light aircraft, the dual frequency nature of the system has several potential issues:
- Since two aircraft on two different ADS-B frequencies must use a ground station to talk to each other, this introduces the ground station as a point of failure, although to be fair, the 1090 signal is dependent on secondary radar scans in any case (and thus cannot operate without a ground station).
- The time taken to traverse the full path from one aircraft, to the ground station, then to the second aircraft adds delay to the signal. This contrasts with two autonomous ADS-B transceivers on UAT, which have a shorter and shorter delay as they converge.
- Aircraft are frequently out of the range of ground-based radar due to altitude. Radar can be blocked by mountains, and typically is not useful for coverage near an airport unless that airport has radar. Thus, approach, departure, and especially taxi/ground-based operations are compromised (a major selling point of the system).
Because of the issues with multilink, many ADS-B manufacturers are designing ADS-B systems as dual-frequency capable.
Flight information services-broadcast (FIS-B)
FIS-B provides weather text, weather graphics, NOTAMs, ATIS, and similar information. FIS-B is inherently different from ADS-B in that it requires sources of data external to the aircraft or broadcasting unit, and has different performance requirements such as periodicity of broadcast.[23]
In the United States, FIS-B services are provided over the UAT link in areas that have a ground surveillance infrastructure.[17][37]
Another potential aircraft-based broadcast capability is to transmit aircraft measurements of meteorological data.[citation needed]
Implementations by country
Australia
Australia has full continental ADS-B coverage above FL300 (30,000 feet).[38] ADS-B equipment is mandatory for all aircraft flying at this altitude. To achieve this level of coverage Airservices Australia operates more than 70 ADS-B ground receiver sites. In Australia, the aviation regulator, the Civil Aviation Safety Authority, mandated a phased requirement for all Instrument Flight Rules (IFR) aircraft to be equipped with ADS-B Out by 2 February 2017. This applies to all Australian aircraft.
Canada
Nav Canada commissioned operational use of ADS-B in 2009 and is now using it to provide coverage of its northern airspace around Hudson Bay, most of which currently has no radar coverage. The service was then extended to cover some oceanic areas off the east coast of Canada including the Labrador Sea, Davis Strait, Baffin Bay, and part of the North Atlantic Tracks around southern Greenland. The service is expected to be later extended to cover the rest of the Canadian Arctic, and to the rest of Canada.[39][40][8][9]
In 2018, Nav Canada issued an aeronautical study[41] proposing a mandate for Aireon-compatible ADS-B Out for all aircraft in Class A Airspace by 2021 and Class B Airspace by 2022, requiring a transponder capable of delivering antenna diversity performance. In response to stakeholder feedback, Nav Canada later announced[42] that such equipment will not be mandated according to that timeline, but rather that suitably equipped aircraft would be handled on a priority basis. The dates upon which equipment will be required for operation in Canadian airspace have been announced as August 10, 2023, for Class A Airspace, May 16, 2024, for Class B Airspace and Class C, D and E no sooner than 2026.[43]
In May 2021, the not-for-profit Canadian In-Flight Information Broadcasting Association announced[44] its intention to build and operate a network broadcasting FIS-B (weather) and TIS-B (traffic) information on 978 MHz. By spring 2022, five ground stations were operating in Ontario, with several more stations planned for Alberta and Saskatchewan. The Canadian network is fully compatible with the United States network. Aircraft can use the same ADS-B In receivers in both countries and the provided services operate seamlessly when crossing the border. CIFIB plans to have about 100 stations operating within a few years. Coverage in Canada will not be coast-to-coast but will focus on areas with higher traffic.
China
An American company ADS-B Technologies created one of the largest and most successful ADS-B systems in the world (an eight-station, 350+ aircraft network that spans more than 1,200 nmi across Central China). This was also the first UAT installation outside the United States. As of March 2009, more than 1.2 million incident/failure-free flight hours have been flown with these ADS-B systems.[citation needed]
Iceland
As of 2010, Isavia is in the process of installing ADS-B across the North Atlantic Ocean.[45] The system is made up by 18 ADS-B receiver stations in Iceland, Faroe Islands, and Greenland.[46][47]
India
The Airports Authority of India (AAI), which manages the country's airspace, first commissioned German company Comsoft to install ADS-B ground stations at 14 airport sites nationwide in 2012. Comsoft finished installing seven new ADS-B ground stations under a second phase of deployment which India subsequently integrated into its ATC system in 2014, thus completing its ground network for automatic dependent surveillance-broadcast (ADS-B) tracking of aircraft.
In line with the International Civil Aviation Organization's aviation system block upgrade plan, AAI has said that its ADS-B network will provide redundant, satellite-based surveillance where radar coverage exists, fill gaps in surveillance where radar coverage is not possible due to high terrain or remote airspace and enable it to share ADS-B data with neighboring countries. The network covers the Indian subcontinent, plus parts of the Bay of Bengal and the Arabian Sea.[48][49]
Sweden
LFV Group in Sweden has implemented a nationwide ADS-B network with 12 ground stations. Installation commenced during the spring of 2006, and the network was fully (technically) operational in 2007. An ADS-B–supported system is planned for operational usage in Kiruna, Sweden, during spring 2009.[needs update] Based on the VDL Mode 4 standards, the network of ground stations can support services for ADS-B, TIS-B, FIS-B, GNS-B (DGNSS augmentation) and point-to-point communication, allowing aircraft equipped with VDL 4-compliant transceivers to lower fuel consumption and reduce flight times.[citation needed]
United Arab Emirates
United Arab Emirates commissioned three operational redundant ADS-B ground stations in early 2009 and is now using ADS-B to provide enhanced coverage of its upper airspace in combination and integrated with conventional surveillance radars.[50][51]
United States
To reduce congestion and cope with growing aircraft traffic, the Federal Aviation Administration has been developing the Next-Generation Air Transportation System (NextGen),[13] including ADS-B. ADS-B equipment is built to meet one of two sets of industry standards, DO-260B and DO-282B.
Aircraft operating in the United States in the airspace classes listed below are required to carry equipment that produces an ADS-B Out broadcast. ADS-B Out broadcasts information about an aircraft through an onboard transmitter to a ground receiver, moving air traffic control from a radar-based system to a satellite-derived aircraft location system.[13]
There is no such mandate for ADS-B In, which receives data and provides it to in-cockpit displays.[52] The FAA airspace requirements intentionally exclude some airspace that is frequently used by general aviation.
Airspace Class | Altitude |
---|---|
A | All aircraft equipped |
B | All aircraft equipped |
C | All aircraft equipped |
E | Where above both 10,000 ft MSL and also above 2,500 ft AGL |
Operators can choose the 1090 megahertz extended squitter broadcast link, or the universal access transceiver broadcast link. FAA did not adopt higher performance standards that would enable all of the initial ADS-B In applications, but these can optionally be adopted.[13]
Equipping aircraft
Fleet: 250,000 GA aircraft that will need ADS-B by 2020 of which 165,000 aircraft are subject to ADS-B Out (Class I and Class II aircraft that generally fly below 18 000 feet).[53] FAA forecasts an increase in the GA fleet from 224,172 aircraft in 2010 to 270,920 aircraft in 2031, growing an average of 0.9% per year.[54]
Funding resources
Recent (April 2011) US federal legislation via House Bill for FAA re-authorization permits[55] an "equipping fund" that includes a portion for some general aviation aircraft. The fund would provide financing at competitive rates backed by loan guarantees.[56] A public-private partnership has been formed as the NextGen Equipage Fund, LLC which is managed by NEXA Capital Partners, LLC.[57]
US implementation timetable
The Federal Aviation Administration ADS-B implementation is broken into three segments each with a corresponding timeline. Ground segment implementation and deployment is expected to begin in 2009 and be completed by 2013 throughout the National Airspace System (NAS). Airborne equipment is user-driven and is expected to be completed both voluntarily based on perceived benefits and through regulatory actions (Rulemaking) by the FAA. The cost to equip with ADS-B Out capability is relatively small and would benefit the airspace with surveillance in areas not currently served by radar. The FAA intends to provide similar service within the NAS to what radar is currently providing (5 nmi en route and 3 nmi terminal radar standards) as a first step to implementation. However, ADS-B In capability is viewed as the most likely way to improve NAS throughput and enhance capacity.[citation needed]
In December 2008, Acting FAA Administrator Robert A. Sturgell gave the go-ahead for ADS-B to go live in southern Florida. The south Florida installation, which consists of 11 ground stations and supporting equipment, is the first commissioned in the United States, although developmental systems have been online in Alaska, Arizona, and along the East Coast since 2004. The completed system will consist of 794 ground station transceivers. The December 2008 action is in compliance with a late-term executive order from George W. Bush which mandated accelerated approval of NextGen.[58]
FAA segment 1 (2006–09)
ADS-B deployment and voluntary equipment, along with rule-making activities. Pockets of development will exploit equipment deployment in the areas that will provide proof of concept for integration to ATC automation systems deployed in the NAS.[59] It is being developed at the FAA's William J. Hughes Technical Center near Egg Harbor City, New Jersey.[3]
FAA segment 2 (2010–14)
ADS-B ground stations will be deployed throughout the NAS, with an in-service decision due in the 2012–2013 time frame. Completed deployment will occur in 2013–14. Equipment rules have been finalized and the current standards are DO-282B for UAT and DO-260B for 1090ES:[59]
- Airport situational awareness – a combination of detailed airport maps, airport multilateration systems, ADS-B systems and enhanced aircraft displays have the potential to improve Airport Surface Situational Awareness (ASSA) significantly, and Final Approach and Runway Occupancy Awareness (FAROA).[60]
- Oceanic In-trail – ADS-B may provide enhanced situational awareness and safety for Oceanic In-trail maneuvers as additional aircraft become equipped.[citation needed]
- Gulf of Mexico – in the Gulf of Mexico, where ATC radar coverage is incomplete, the FAA is locating ADS-B (1090 MHz) receivers on oil rigs to relay information received from aircraft equipped with ADS-B extended squitters back to the Houston Center to expand and improve surveillance coverage.[3]
- Terminal Airspace – ADS-B is currently in service for two terminal airspace areas, Louisville, Kentucky, and Philadelphia, Pennsylvania.
FAA segment 3 (2015–20)
ADS-B In equipment will be based on user-perceived benefit but is expected to be providing increased situational awareness and efficiency benefits within this segment. Those aircraft that choose to equip in advance of any mandate will see benefits associated with preferential routes and specific applications. Limited radar decommissioning will begin in the time frame with an ultimate goal of a 50% reduction in the secondary surveillance radar infrastructure.[citation needed]
On 27 May 2010, the FAA published its final rule mandating that by 2020 all aircraft owners will be required to have ADS-B Out capabilities when operating in any airspace that currently requires a transponder (airspace classes A, B, and C, and airspace class E at certain altitudes).[61]
On 14 June 2012, FreeFlight Systems and Chevron received STC for the first rule-compliant ADS-B installation in GOMEX helicopters that was awarded by the FAA.
Early adopters
- Cargo Airline Association
- Cargo carriers, notably UPS.[3] They operate at their hub airports largely at night. Much of the benefit to these carriers is envisioned through merging and spacing the arriving and departing traffic to a more manageable flow. More environmentally friendly and efficient area navigation (RNAV) descent profiles, combined with CDTI, may allow crews to eventually aid controllers with assisted visual acquisition of traffic and limited cockpit-based separation of aircraft. The benefits to the carrier are fuel and time efficiencies associated with idle descent and shorter traffic patterns than typical radar vectoring allows.[citation needed]
- Embry-Riddle Aeronautical University
- ERAU has equipped its training aircraft at its two main campuses in Florida and Arizona with UAT ADS-B capability as a situational safety enhancement. The university has been doing this since May 2003, making it the first use in general aviation.[62] With the addition of the Garmin G1000 flight instrument system to their fleet in 2006, ERAU became the first fleet to combine a glass cockpit with ADS-B.[63]
- University of North Dakota
- UND has received an FAA grant to test ADS-B and has begun to outfit their Piper Warrior fleet with an ADS-B package.[64]
Privacy
The FAA in America has come up with two systems to address privacy concerns[65]
- Limiting Aircraft Data Displayed (LADD): Aircraft owners or designated representatives may request limiting aircraft data displayed (formally referred to as blocking) or unblocking flight tracking data. Flight tracking services that draw the data from FAA agree to block the information, though as noted elsewhere in this article, the data are unencrypted and may be available from non-FAA sources.
- Privacy ICAO Aircraft (PIA): Program to improve the privacy of eligible aircraft by enabling aircraft owners to request an alternate, temporary ICAO aircraft address, which will not be assigned to the owner in the Civil Aviation Registry (CAR). These are used in conjunction with a third party call sign:[66] DCM (Garmin/Fltplan.com),[67] FFL (ForeFlight),[68] FWR (FlightAware),[69] XAA (ARINCDirect/Collins Aerospace).[70]
System design considerations
A concern for any ADS-B protocol is the capacity for carrying ADS-B messages from aircraft, as well as allowing the radio channel to continue to support any legacy services. For 1090 ES, each ADS-B message is composed of a pair of data packets. The greater the number of packets transmitted from one aircraft, the fewer aircraft that can participate in the system, due to the fixed and limited channel data bandwidth.
System capacity is defined by establishing a criterion for what the worst environment is likely to be, then making that a minimum requirement for system capacity. For 1090 ES, both TCAS and ATCRBS/MSSR are existing users of the channel. 1090 ES ADS-B must not reduce the capacity of these existing systems.[citation needed]
The FAA national program office and other international aviation regulators are addressing concerns about ADS-B[71] non-secure nature of ADS-B transmissions. ADS-B messages can be used to know the location of an aircraft, and there is no means to guarantee that this information is not used inappropriately. Additionally, there are some concerns about the integrity of ADS-B transmissions. ADS-B messages can be produced, with simple, low-cost measures, which spoof the locations of multiple phantom aircraft to disrupt safe air travel. There is no foolproof means to guarantee integrity, but there are means to monitor this type of activity. This problem is however similar to the usage of ATCRBS/MSSR where false signals also are potentially dangerous (uncorrelated secondary tracks).[citation needed]
There are some concerns about ADS-B dependence on satellite navigation systems to generate state vector information,[72] although the risks can be mitigated by using redundant sources of state vector information; e.g., GPS, GLONASS, Galileo or multilateration.[citation needed]
There are some general aviation concerns that ADS-B removes anonymity of the VFR aircraft operations.[71] The ICAO 24-bit transponder code specifically assigned to each aircraft will allow monitoring of that aircraft when within the service volumes of the Mode-S/ADS-B system. Unlike the Mode A/C transponders, there is no code "1200"/"7000", which offers casual anonymity. Mode-S/ADS-B identifies the aircraft uniquely among all in the world, in a similar fashion as a MAC address for a network interface controller or the International Mobile Equipment Identity (IMEI) of a GSM phone.[citation needed] However, the FAA is allowing UAT-equipped aircraft to utilize a random self-assigned temporary ICAO address in conjunction with the use of beacon code 1200. 1090 ES-equipped aircraft using ADS-B will not have this option.[73]
In order for the ADS-B system to function to the fullest extent, equipment for all aircraft in the airspace is required. This demands that transponder technology be scalable from the smallest aircraft to the largest aircraft to allow for 100% equipage for any given airspace. Current transponder technology is capable of equipping larger, traditional aircraft but a new type of transponder is required for equipping aircraft that are smaller and lighter or don't have electrical systems like the large traditionally transponder-equipped aircraft. The requirements for these smaller and lighter aircraft are mainly size, weight, and power (SWAP) and transponder technology must allow for equipage of these types of aircraft to enable saturation of ADS-B for total visibility in any given airspace.[citation needed]
On 7 June 2002 the FAA published a historical overview of its decision on the ADS-B link architecture for use in the National Airspace System (NAS).[17]
Technical and regulatory documents
- Minimum Aviation System Performance Standards (MASPS)
- Minimum Operational Performance Standards (MOPS)
- DO-242A — ADS-B MASPS. Describes system-wide operational use of ADS-B.
Satellite (space-based) ADS-B Collection
A significant step forward for ADS-B is the reception by artificial satellites of the ADS-B signal. It was tested for the first time in 2013 on ESA's PROBA-V[74] and it is being deployed by companies like Spire Global using low-cost nanosatellites. Aireon is also working on space-based ADS-B with the Iridium satellite network, a LEO (Low Earth Orbit) satellite network that was originally created to deliver phone and data service anywhere on the planet. By capturing ADS-B position data from aircraft flying below the satellite, the network will give the following capabilities:
- Air traffic control using surveillance-based separation standards will be possible over water, in areas that radar does not currently cover. Currently, air traffic control uses the larger procedural separation standard in oceanic and remote areas.
- As is currently possible in radar-covered areas, a position history will be available for lost aircraft, as in the case of Malaysia Airlines Flight 370.
The system only receives ADS-B on aircraft broadcasting on the 1090 MHz frequency. This limits the system generally to airliners and business aircraft, despite the fact that small aircraft are frequently off the radar due to mountains blocking the signal at low altitudes. The system could be compromised by smaller, private aircraft with exclusive belly-mounted ADS-B antennas, due to the aircraft hull blocking the signal.
The rationale for using the Iridium satellite network for this new capability was due to:
- The Iridium satellites fly very low and thus can receive the ADS-B out signals more reliably (transponders and ADS-B were designed for ground reception).
- Iridium satellites are replaced relatively frequently due to the increased air friction at their lower altitude, and thus lower lifespan. Thus the system would be deployed on iridium faster.
- Iridium provides worldwide coverage, including the poles.
In September 2016, Aireon and FlightAware announced a partnership[75] to provide this global space-based ADS-B data to airlines for flight tracking of their fleets and, in response to Malaysia Airlines Flight 370, for compliance with the ICAO Global Aeronautical Distress and Safety System (GADSS) requirement for airlines to track their fleets.[76] In December 2016, Flightradar24 entered an agreement with Gomspace for space-based tracking in 2016.[77]
SpaceX subsequently placed 66 operational and 9 spare Iridium satellites in orbit over the course of 8 launches between 14 January 2017 and 11 January 2019. Another 6 spare satellites remain on the ground.
The ICAO describes space-based ADS-B as a technology equalizer, offering developing nations an airspace surveillance capability. By 2020, 34 nations will deploy the system, including the 17 members of the Asecna in Africa, and the Cocesna air navigation services agency in Central America. More frequent updates in the North Atlantic Tracks allowed reducing longitudinal separation from 40 to 14 nmi (74 to 26 km) and lateral separations from 23 to 19 nmi (43 to 35 km). The FAA plans an evaluation in the Caribbean airspace from March 2020 until 2021, to complement the unreliable Grand Turk Island radar which allows reducing separation from 30 to 5 nmi (55.6 to 9.3 km).[78]
See also
- Acronyms and abbreviations in avionics
- ASDE-X
- Automatic Identification System, a conceptually similar system for marine vessels
- Advanced Train Control System, a conceptually similar system for railroads
- Automatic Packet Reporting System (APRS), a conceptually similar GPS-based tracking system in the amateur radio service
- DO-212, minimal operational performance standards for airborne automatic surveillance (ADS)
- Eurocat (air traffic control)
- FLARM
- Flight tracking
- Free flight (air traffic control)
- GPS aircraft tracking
- Portable collision avoidance system
- Traffic collision avoidance system
References
This article incorporates public domain material from websites or documents of the Federal Aviation Administration.
- ^ "How ADS-B works". Airservices Australia. 28 November 2012. Retrieved 26 July 2014.
- ^ Richards, William R; O'Brien, Kathleen; Miller, Dean C (2010). "New Air Traffic Surveillance Technology" (PDF). Boeing Aero Quarterly. 2. Retrieved 7 April 2014.
- ^ a b c d Gugliotta, Guy (16 November 2009). "An Air-Traffic Upgrade to Improve Travel by Plane". The New York Times.
- ^ "AUTOMATIC DEPENDENT SURVEILLANCE – BROADCAST (ADS-B) OUT BASED ATS SURVEILLANCE SERVICES" (PDF). www.aai.aero. Archived from the original (PDF) on 4 March 2016. Retrieved 22 May 2022.
- ^ Automatic Dependent Surveillance—Broadcast (ADS–B) Out Performance Requirements To Support Air Traffic Control (ATC) Service (PDF), US: GPO, December 2010
- ^ "COMMISSION IMPLEMENTING REGULATION (EU) No 1207/2011 of 22 November 2011 laying down requirements for the performance and the interoperability of surveillance for the single European sky" (PDF).
- ^ Davidson, Jason (23 September 2013). "ADS-B Requirements Coming into Effect". Universal Weather. Archived from the original on 28 September 2013. Retrieved 30 September 2013.
- ^ a b Fredericks, Carey (26 January 2009). "Breakthrough technology brings air traffic surveillance to Hudson Bay". Wings Magazine. Retrieved 19 March 2020.
- ^ "Advisory Circular (AC) No. 700-009". 28 February 2019. Retrieved 17 September 2020.
- ^ Freeze, Christopher (December 2021). "Award-Winning Teamwork". Air Line Pilot: 23–24.
- ^ a b c d e Free flight systems, archived from the original on 17 November 2012, retrieved 19 April 2011
- ^ a b c d e Final Rule for ADS‐B Out (PDF), Federal Aviation Administration, 28 May 2010
- ^ What portable ADS-B receivers don't tell you, 4 February 2014
- ^ "Surveillance broadcast", En route (general information), US: FAA, archived from the original on 3 May 2011
- ^ "Broadcast services", ADS‐B, US: FAA, archived from the original on 29 April 2011
- ^ a b c d e Scardina, John (7 June 2002). "Overview of the FAA ADS-B Link Decision" (PDF). Federal Aviation Administration. Archived from the original (PDF) on 16 March 2007.
{{cite journal}}
: Cite journal requires|journal=
(help) - ^ Babbitt, Randy (5 May 2011), Speech, Aero Club of Metro Atlanta (FAA Administrator).
- ^ a b c d e Kunzi, Fabrice; Hansman, R John (16–17 July 2009), "Identification of ADS-B User Benefits to Incentivize GA Equipage", JUP Quarterly Meeting (presentation), MIT International Center for Air Transportation
- ^ "AOPA demos ADS-B for Civil Air Patrol", What's new, 4 March 2003, archived from the original on 22 July 2016
- ^ Fact sheet, US: FAA
- ^ "Avionics driving efficiency gains", Aviation Today (feature), February 2009
- ^ a b c d e f g h Minimum Aviation System Performance Standards for Automatic Dependent Surveillance-Broadcast (ADS-B). RTCA. 25 June 2002. DO-242A.
- ^ "Air Traffic Control Systems Vulnerabilities Could Make for Unfriendly Skies [Black Hat] — SecurityWeek.Com". 27 July 2012.
- ^ Strohmeier, Martin; Lenders, Vincent; Martinovic, Ivan (2015). "Lightweight Location Verification in Air Traffic Surveillance Networks" (PDF). Proceedings of the 1st ACM Workshop on Cyber-Physical System Security. pp. 49–60. doi:10.1145/2732198.2732202. ISBN 9781450334488. S2CID 15259041.
- ^ "Decoding ADS-B position".
- ^ Mozdzanowska, Aleksandra; et al. (18–20 September 2007), "Dynamics of Air Transportation System Transition and Implications for ADS-B Equipage", 7th Aviation Technology, Integration and Operations Conference (ATIO), Belfast, Northern Ireland: AIAA
- ^ Minimum Operational Performance Standards for Universal Access Transceiver (UAT) Automatic Dependent Surveillance – Broadcast. RTCA. 29 July 2004. DO-282A.
- ^ Minimum Operational Performance Standards for 1090 MHz Extended Squitter Automatic Dependent Surveillance – Broadcast (ADS-B) and Traffic Information Services – Broadcast (TIS-B). RTCA. 10 April 2003. DO-260A.
- ^ a b ICAO (2012). ICAO Doc 9871, Technical Provisions for Mode S and Extended Squitter (2 ed.). International Civil Aviation Organization. ISBN 978-92-9249-042-3.
- ^ Kunzi, Fabrice (30 August 2010), "ADS-B Avionics Architecture: 1090ES and UAT", ADS‐B forga, archived from the original on 8 July 2011
- ^ FIS-B Product Summary, ITT, 25 January 2011
- ^ a b c "FAA Announces Automatic Dependent Surveillance-Broadcast Architecture" (Press release). FAA Office of Public Affairs. 1 July 2002. APA 27-02. Archived from the original on 22 October 2012. Retrieved 21 February 2011.
- ^ "Approval requirements for Air — Ground Data Link and ADS — B in support of Interoperability requirements" (PDF). European Aviation Safety Agency. 21 November 2012.
- ^ "TSO C‐166A", Regulatory & guidance library (PDF), US: FAA
- ^ "Multilateration: Airport Surface". ERA a.s.. Retrieved 30 April 2013.
- ^ "ADS-B – ADS-B In Pilot Applications". faa.gov. Retrieved 30 April 2022.
- ^ Kelly, Emma (23 December 2009), "Australia in world first for nationwide ADS-B coverage", Flight International
- ^ "Aviation Safety Letter". Transport Canada, Civil Aviation. January 2007. Retrieved 1 May 2007.
- ^ "AERONAUTICAL STUDY: Canadian ADS-B Out Performance Requirements Mandate" (PDF). Nav Canada. August 2018. Retrieved 5 March 2020.
- ^ "NOTICE OF CHANGE UPDATE Canadian ADS-B Out Performance Requirements Mandate" (PDF). Nav Canada. Retrieved 5 March 2020.
- ^ "NAV CANADA ADS-B Performance Requirements". www.navcanada.ca. Retrieved 5 December 2022.
- ^ "CIFIB national network build". Wings Magazine. 28 May 2021. Retrieved 10 June 2021.
- ^ "Annual Report 2010" (PDF). Isavia. p. 26. Archived from the original (PDF) on 24 May 2013. Retrieved 2 February 2012.
- ^ "ADS-B". Isavia. Retrieved 21 September 2018.
- ^ "Isavia Signs Agreement to Deploy Space-Based ADS-B". Isavia. Retrieved 21 September 2018.
- ^ Carey, Bill. "India Completes ADS-B Ground Network Installation | AIN". Aviation International News.
- ^ ICAO; AAI (April 2013). "ADS-B Implementation in India" (PDF).
- ^ "HH Sheikh Mohamed bin Zayed Opens Sheikh Zayed Centre" (Press release). UAE: GCAA. November 2009. Retrieved 13 May 2010.
- ^ "Further ADS-B Installations in Abu Dhabi through ComSoft" (Press release). ComSoft. March 2009. Archived from the original on 29 April 2009. Retrieved 13 May 2010.
- ^ "Next gen to guide you gate to gate", Flight planning (article), AOPA, 2 November 2011
- ^ Shaver, Timothy 'Tim' (29 April 2011), "FAA Avionics Maintenance Branch Manager", in Thurber, Mett (ed.), Dealers delight in new avionics at AEA'11, Avionics
- ^ "Fiscal Years 2011–31", Forecast (fact sheet), FAA, 15 February 2011, archived from the original on 22 September 2013
- ^ H.R. 658 section 221 (c)
- ^ Aviation Week, 5 April 2011
- ^ Nexa Capital Partners
- ^ "FAA Officially Launches Radar's Replacement", Flying Magazine, 136 (3): 18, 9 March 2009
- ^ a b "Schedule", Surveillance and Broadcast Services, US: FAA, archived from the original on 28 October 2010
- ^ DO-289 v2 E&F
- ^ "Automatic Dependent Surveillance–Broadcast (ADS-B) Out Performance Requirements to Support air traffic control (ATC) Service". Federal Aviation Administration. 27 May 2010.
- ^ "Embry-Riddle Becomes First in General Aviation to Use Revolutionary ADS-B System". Erau. 13 May 2003. Archived from the original on 12 January 2008. Retrieved 27 July 2007.
- ^ "Embry-Riddle Fleet First to Combine Glass Cockpit and ADS-B". 3 February 2006. Archived from the original on 16 December 2007.
- ^ "UND Aerospace Researcher Awarded $302,459 Grant To Study Safety-Enhancing Technology". University of North Dakota. 17 November 2006. Retrieved 3 May 2007.
- ^ maxflight (23 February 2022). "692 ADSBexchange". Airplane Geeks Podcast. Retrieved 1 March 2022.
- ^ "ADS-B Privacy | Federal Aviation Administration". faa.gov. Retrieved 29 July 2024.
For the purposes of this program, a third-party call sign can be obtained from FlightPlan, ForeFlight, FlightAware, or ARINCDirect.
- ^ "DCM Call Signs Versus FAA Blocking". flttrack.fltplan.com. Retrieved 29 July 2024.
- ^ "ForeFlight - Call Signs". ForeFlight. Retrieved 29 July 2024.
- ^ "Privacy ICAO Address (PIA) - FlightAware". FlightAware. Retrieved 29 July 2024.
- ^ AvBuyer. "BizAv Privacy: How to Fly Incognito in the USA". avbuyer.com. Retrieved 29 July 2024.
- ^ a b "Will ADS-B increase safety and security for aviation?". AirSport Corporation. August 2000. Archived from the original on 9 February 2007.
- ^ "Vulnerability assessment of the transportation infrastructure relying on GPS" (PPT). USCG Navigation Center. United States Coast Guard. 5 October 2001. Retrieved 16 September 2008.
- ^ "FAA Advisory Circular 20-165A Airworthiness Approval of Automatic Dependent Surveillance — Broadcast (ADS-B) Out Systems". Federal Aviation Administration. 7 November 2012.
- ^ esa. "Proba-V maps world air traffic from space". European Space Agency. Retrieved 22 March 2018.
- ^ "Aireon and FlightAware Partner to Launch GlobalBeacon Airline Solution for ICAO Airline Flight Tracking Compliance". 21 September 2016. Retrieved 21 September 2016.
- ^ "Update on GADSS-Related Global Aircraft Tracking Initiatives". Retrieved 21 September 2016.
- ^ "Satellite flight tracking – Flightradar24 Blog". www.flightradar24.com. July 2016.
- ^ Bill Carey (29 October 2019). "Space-Based ADS-B Makes Global Inroads". Aviation Week & Space Technology.
Further reading
- Richards, Michael 'Mike' (2010). Virtual Radar Explained. G4WNC. Radio Society of Great Britain. ISBN 978-1-905086-60-3.
External links
- Automatic Dependent Surveillance-Broadcast (ADS-B) (official website), US: FAA ADS-B Broadcast Services (PDF) (official website), US: FAA
- "ADS-B In the Gulf of Mexico", Aviation News, US: FAA, archived from the original on 7 June 2010
- "ADS‐B", News Archive, AOPA, 11 July 2007, archived from the original on 17 August 2007
- "ADS‐B", FedEx Ordered ADS-B Security Whistleblower to Psychiatric Exam, JetPilots.com, 31 May 2017, archived from the original on 11 December 2018, retrieved 31 July 2019
- "ADS‐B", Nextgen and Noise Pollution the FAAs Carte Blanche to Send Planes Streaming Over Our Houses, medium.com, 31 May 2017, archived from the original on 18 August 2019, retrieved 18 August 2019
- ADS-B Monitor - a free tool to decode, display and log ADS-B messages